I'm looking at this multifunction setup and curious what wood folks are using for something this size that rolls around. Are people going with construction lumber for the frame and something nicer for the top, or just building…
The plan mentions turnbuckles holding the jig to the table. I'm wondering how that actually locks down during a cut - does the clamp pressure stay consistent as you feed the work, or do you need to re-tension between circles? And…
A template-guided mortise jig sounds like the kind of thing where repeatability could get sketchy if the fence or workpiece clamp has any slop. Are people finding the jig itself holds position well enough for batch work, or does…
Lift-off panels sound smart for maintenance, but I'm curious about the design underneath. With a bench sitting on a patio, how's the airflow and drainage handled? Does water pool between the base and the storage box, or is there…
The Victorian Gothic inspiration caught my eye. Before building this, I'm wondering how the proportions read in a contemporary room. Does the architectural detailing feel intentional or fussy depending on where it's placed?…
Bathroom shelves get humid and take a lot of weight. Is this plan meant for thin plywood or solid lumber? Curious if people usually go thicker for vanity areas, or if that's overthinking it on a budget build.
I built a router circle jig out of scrap plywood and it works great but i'm trying to figure out the practical limits on radius size. Mine has a pivot pin about 3 inches from the bit center at minimum, and i can extend to about…
The floating platform with rope connections sounds beautiful, but I'm wondering about real-world durability. How long before rope deteriorates outdoors, especially if it gets wet regularly? Are people replacing them annually, or…
With desk organizers, I'm always wondering how much depth actually works. Are you imagining something shallow for pens and notepads, or deep enough to stash cables and chargers too? And does the layout assume a standard desk…
All plywood construction makes me curious about finish choices here. Are people planning to paint these, or doing a stain and poly approach? Plywood edges can be tricky either way. Wondering if anyone's built this and whether the…
I drew a bench to build from a scrap pile: three 8 ft studs (2x4), one 1x4, one 3/4 ply offcut. No bought hardware, screws only, longest part 40 in. Seat 17 high, 16.5 deep, legs splayed 8 degrees. Full sheet, parts table, cut…
Picked up a dresser at an estate sale and started stripping it, pretty sure there's something nice under all that old paint. I've got it down to bare wood in a few spots and the grain looks really tight and dark, could be walnut…
My router plane keeps losing its depth setting partway through a dado, usually right when i'm sneaking up on the final fit. Tried tightening the lock but it still creeps. Not sure if it's the iron collar or something with the…
Finally getting around to lighting the underside of my wall cabinet shelf above the bench and wondering if regular LED strip tape is good enough or if i should go with something brighter. The cheap stuff always seems dim once its…
Finally got my drill press set up and when i chuck a bit there's a tiny wobble when it spins. Is a little runout just a fact of life on budget machines or should i be worried about bad bearings? Also noticed it more with longer…
Ive been doing 4 coats of wipe on poly on a walnut side table and im wondering how long folks actually wait between coats in a cool garage. The can says 2-3 hours but at like 55 degrees it still feels tacky at 4. Curious if…
I have two nice pieces of walnut that I plan to use to make a side table. Both pieces are variegated in color – mostly dark in the middle and lighter on the outsides. Neither piece is wide enough to use alone for the table top.…
The dual-purpose angle here caught my eye. Before I dig into building one, is anyone using these as an actual storage base for a mobile tool cart or workbench station? The bench/chest idea is solid, but I'm wondering if the…
Been going back and forth on this for a while. I clean most of my dadoes with a chisel but the floor is never as consistent as i'd like, especially across wider cuts. Is a router plane actually worth it for this or am i just not…
Jewelry boxes are a good fit for that kind of detail work. Curious whether you'd lean toward dovetails for the visual, or if there's a reason the plan calls for a particular joint at the corners. The curly maple would show either…