Building a dedicated circle cutting jig and trying to figure out what range of radii is actually useful before I commit to the rail length. I'm thinking a 3/4" ply base with a T-track slot so the pivot pin slides and locks,…
Been using a cheap corded ROS for years and finally want to upgrade to something decent. I keep going back and forth between the Bosch 1250DEVS and the Makita BO5041, both are around the same price right now. Anyone running…
Been using my table saw with a roller stand for plywood but it's kind of a pain to maneuver full sheets solo. Thinking about grabbing a track saw to handle the initial rip cuts in the driveway before bringing stuff inside. Anyone…
Been using my table saw with a roller stand for plywood but it's a pain to manage full sheets alone. Thinking about picking up a track saw to make it easier, anyone made the switch or use both? Wondering if it's actually worth…
Upgraded from my mini to a Rikon 70-220 midi last week and honestly the extra swing is already making me rethink every blank i own. First bowl attempt on it was a fat chunk of walnut and man the torque difference is night and…
Been going back and forth on this for my next build and want some real world opinions. I know quarter sawn is more stable and honestly the ray fleck on oak is gorgeous, but the price difference at my local yard is pretty…
Been thinking about this a lot lately carving a relief panel in basswood. Going with the grain feels smooth but even a slight angle against it and the gouge wants to dive or tear. I know in theory you follow the grain but in…
Tried ironing on edge banding to a shelf I built and the corners keep lifting no matter how much pressure i put on. I'm using a regular clothes iron, maybe that's the problem? Already pressed it down twice and it looks fine for a…
Been using the blue tape and CA glue method for holding down thin plywood on my spoilboard and it works great for small stuff, but anything over like 18 inches tends to lift a corner mid cut and ruins the piece. Running a pretty…
Pulled off the top layer of paint on an old dresser I picked up at an estate sale and turns out there's walnut underneath. Kind of changes my whole plan now, not sure if i should keep stripping and do a clear finish or try to…
Been carving spoons off and on for a few months now and i keep getting these little fuzz tears on the bowl interior no matter how sharp i go. Wondering if i'm just fighting the grain the wrong direction or if that's kinda normal…
Been running a harbor freight mini for about two years and i'm just constantly fighting the limitations, especially on bigger bowl blanks. Looking at the Jet 1221VS and the Rikon 70-105 but honestly the specs blur together after…
Been using my table saw for sheet goods forever but breaking down 4x8s solo is getting old. A track saw seems way faster for that first rough cut but i'm not sure it justifies the price if you already own a decent table saw.…
Been going back and forth on this for a while now. I use a router plane to flatten the bottom of dadoes but sometimes wonder if careful paring with a sharp chisel would be just as consistent. Anyone settled on one approach over…
Running a 1/4 inch upcut spiral in 3/4 Baltic birch and getting some nasty fuzz on the top surface, especially on pocket cuts. I'm at 18000 RPM and around 60 ipm feed rate with a 0.1 inch depth per pass. Anyone dialed this in…
Picked up a beat up dresser at an estate sale for almost nothing, and after stripping the top I found what looks like genuine walnut under about three layers of paint. Now i'm debating whether to strip the whole thing or just the…
Been thinking about building a DIY track guide for my circular saw instead of buying a Festool setup i cant afford. I made a simple one from scrap MDF before and it helped a lot, but wondering if there's a better way to do it.…
Been running a Harbor Freight mini lathe for about two years and I keep hitting its limits, mostly on bowl blanks wider than 8 inches. Looking at the Jet 1221VS and the Rikon 70-105 but honestly the specs start blurring together…
Had another close call at the shop today and it reminded me that a lot of people still reach behind or over the blade to clear offcuts while it's spinning. Get a push stick or a scrap piece of wood and knock it clear from the…
I keep seeing people say you should use poplar or pine for beginner stuff but then other people say just use whatever is cheap at the hardware store. I'm about to build a small shelf and honestly have no idea if it matters or if…